How to Fix D-Link Extender Blinking Red?

 

The Dlink extender red light indicates the connection failure between the extender and the router. Several reasons could be responsible for this problem. The D-Link extender is an excellent WiFi range extender that amplifies the range of your existing WiFi. With proper setup, you can eliminate the dead zones in your house with the help of this networking device. However, if you fail to set up the extender accurately, you could face numerous issues with the extender. An example is the D’Link WiFi extender blinking red light, which is a common issue among users.

If you are facing this issue as well, you don’t have to worry. Today, we will discuss why the extender is flashing the red light. Afterward, we’ll go over the ways to resolve this issue. Keep reading ahead to find out more!

Why is D’link Wifi Extender Blinking Red Light?

• Power outage

• Improper cable connections

• Extender is too far from the router

• Outdated firmware

• An internal issue with the router and the extender

Troubleshooting DLink Extender Red Light

Now that we know the issues responsible for the D-Link extender blinking red light, we can troubleshoot it. You can troubleshoot the problem by following the below methods:

Reboot Your D-Link Extender

• The first method you can try to fix this issue is the reboot.

• Rebooting the extender fixes any internal glitches and bugs within the device.

• To reboot the device, you just need to turn OFF the extender and unplug it.

• Give the extender some time to cool down.

• After a few seconds, you can power the extender back ON.

• Now, the D’Link WiFi extender blinking red light issue should be gone.

• While you’re at it, you can also reboot the router.

Check Power Socket and Wiring

• The extender requires a constant and stable power source to work efficiently.

• Therefore, you must keep the extender plugged into an electrical outlet 24/7.

• Check for any power outages, if there are, you will have to wait till the power is back.

• You can also try plugging the extender and the router into another power socket.

• This should solve the D-Link extender blinking red light.

• Also, check the cable connection between the router and the modem.

• Ensure there are no loose connections.

Update the D-Link Firmware if Available

• Sometimes, due to outdated firmware versions, the devices start acting up.

• To troubleshoot the DLink extender red light issue, you can update the D-link firmware.

• Initially, log into the extender’s user interface using your login credentials.

• When the user interface displays, go to the ‘Management’ section.

• Under it, click the ‘Firmware Upgrade' option.

• Now, you can either proceed with the ‘Automatic’ upgrade or the ‘Manual’ upgrade.

• For the Automatic upgrade, tap the ‘Check for Update option.

• If it shows an available update, you can click ‘Upgrade Firmware’ to initiate it.

• Whereas for the Manual upgrade, you will have to upload the file manually.

• At last, once the upgrade is complete, the extender will reboot.

• This should resolve the issue with the extender.

Distance Between Router and Extender

• The most common reason for the D-Link extender blinking red light is the distance between the extender and the router.

• After the setup, you can relocate the extender near the dead zones.

• However, while choosing a location, you must ensure the extender is inside the router’s range.

• If you place the extender too far from the router, it will have trouble receiving its network.

• Therefore, place the extender halfway between the router and the areas you receive bad or no signal.

Reset Your D-Link Wifi Extender

• If the D’Link WiFi extender blinking red light issue persists, you will have to reset D-Link extender.

• The reset will eliminate any internal issues with the device, and make the device as good as new.

• To begin with, locate the reset button on the extender.

• You can find it on the rear of the extender.

• Now, press and hold the reset button using a sharp object.

• After 10 seconds, you can let go of the reset button.

• At last, the extender will reboot to bring the reset into effect.

• When the extender turns back on, the issue should be fixed now.

• Now that the factory default settings of the extender are back, you can reconfigure the extender.

• You can try resetting the router as well to eliminate any issues with the router.

Bottom Line

These are some methods you can use to fix the DLink extender red light issue. If there are any other issues you are facing with your D-Link range extender, you can get in touch with our team. We’ll help you troubleshoot it effectively.